Optical Flow Sensor

Excl. VAT: £23.99 Incl. VAT: £28.79

Availability: Pre Order

Pre-Order
Excl. VAT: £23.99 Incl. VAT: £28.79
We Accept: Visa Paypal Amex Master Card
Description

Optical Flow Sensor

 
This optical flow mouse sensor and a lens-mount assembly ( ADNS3080 ). It can add aditional features to your vehicles, the use of the optical flow sensor can be used for horizontal altitude hold for ArduCopter quads and helis, odometry and obstacle avoidance.
 
The Optical Flow Sensor will be supported in the ArduCopter code from 2.6 and above.

NOTE:  This optical flow sensor comes assembled. The sensor will not perform well in dimly lit environments or under fluorescent lights.

Features & Specifications
  • ADNS-3080 optical sensor.
  • High speed motion detection.
  • Up to 6400 fps update rate.
  • 30x30 pixel resolution.
  • Includes an 8mm lens which can be replaced, depending on the use requirements.
  • Standard M12 x 0.5 lens mount.
 
Documents & Instructions

The libraries needed for the code can be found here.
Set up instructions can be found here.
Eagle files are here.

Reviews

Customer Reviews 7 item(s)

perfect
fast shipping, thank you.
Your Rating
Review by Gabriele Facchini / (Posted on 06/08/2013)
outstanding service
I purchase quite a bit online but BYOD is the standard that I wish more people would work to emulate.

Fast delivery. Helpful. Informative
Your Rating
Review by Mike Stone / (Posted on 06/08/2013)
perfect
more efficient than the royal mail :)
keep it up!
Your Rating
Review by herve pellarin / (Posted on 06/08/2013)
Avoids expensive collisions,fingers crossed.
Not had the pleasure yet but have seen some promising videos of its use.
Your Rating
Review by Mike Perkins / (Posted on 06/08/2013)
Optical Flow Sensor
Could not find a Docu for Soldering, no hint that this item will not be supportet by APM 2.0.
Hopefully later

Thank you for your review Gehard:

I have updated the product page to show the APM support options at this time, it's only "ArduPilot Mega 1", the Solder Doc's and supported systems are above in the "Set up instructions can be found here" link in the Documents & Instructions section at the bottom of the product page.

Regards

Martin.
Your Rating
Review by Gerhard Siemons / (Posted on 06/08/2013)
OF sensor.
Looks good and seems to work ok with Arduino. Loooking forward to using it on my Quad.
Your Rating
Review by Simon Warner / (Posted on 06/08/2013)
Optical Flow Sensor
looks ok, but not tested
Your Rating
Review by Reinhold Gamer / (Posted on 06/08/2013)

Customer Reviews 7 item(s)

perfect
fast shipping, thank you.
Your Rating
Review by Gabriele Facchini / (Posted on 06/08/2013)
outstanding service
I purchase quite a bit online but BYOD is the standard that I wish more people would work to emulate.

Fast delivery. Helpful. Informative
Your Rating
Review by Mike Stone / (Posted on 06/08/2013)
perfect
more efficient than the royal mail :)
keep it up!
Your Rating
Review by herve pellarin / (Posted on 06/08/2013)
Avoids expensive collisions,fingers crossed.
Not had the pleasure yet but have seen some promising videos of its use.
Your Rating
Review by Mike Perkins / (Posted on 06/08/2013)
Optical Flow Sensor
Could not find a Docu for Soldering, no hint that this item will not be supportet by APM 2.0.
Hopefully later

Thank you for your review Gehard:

I have updated the product page to show the APM support options at this time, it's only "ArduPilot Mega 1", the Solder Doc's and supported systems are above in the "Set up instructions can be found here" link in the Documents & Instructions section at the bottom of the product page.

Regards

Martin.
Your Rating
Review by Gerhard Siemons / (Posted on 06/08/2013)
OF sensor.
Looks good and seems to work ok with Arduino. Loooking forward to using it on my Quad.
Your Rating
Review by Simon Warner / (Posted on 06/08/2013)
Optical Flow Sensor
looks ok, but not tested
Your Rating
Review by Reinhold Gamer / (Posted on 06/08/2013)

Write Your Own Review

Only registered users can write reviews. Please, log in or register